Turbochargers explained

How a turbo is built, how to read its specs, and which parts bolt together.

Parts

Exhaust drives the turbine on one end of a shaft; the compressor on the other end pushes air into the engine.

oil inoil out4312657
  1. 1

    Compressor housing. Slows the air leaving the compressor wheel, turning its speed into pressure. The outlet feeds the intercooler.

  2. 2

    Compressor wheel. Draws air in at the inducer and throws it out at the exducer. Its size sets how much air the turbo can move.

  3. 3

    Backplate. Seals the compressor housing to the centre section. A T04 backplate on a T3 core makes a T3/T4 hybrid.

  4. 4

    Centre section (CHRA). Carries the shaft bearings. Oil enters at the top and drains from the bottom; many cores have coolant ports too.

  5. 5

    Turbine wheel and shaft. Exhaust spins it, and the shaft drives the compressor wheel. A larger wheel lowers back pressure but spools later.

  6. 6

    Turbine housing. Guides exhaust onto the turbine wheel. Its A/R trades early boost against top-end flow.

  7. 7

    Wastegate actuator. A spring-loaded diaphragm. Once boost overcomes the spring, it opens the wastegate and exhaust bypasses the turbine.

A/R and trim

A/R 0.63

Medium housing. The usual choice for a street engine.

A is the cross-section of the housing’s passage at the tongue, where the scroll starts. R is the distance from the shaft centre to the middle of that section. A smaller A/R speeds exhaust onto the wheel.

Trim 52

The inducer is 52% of the exducer’s area.

A compressor wheel seen from its inlet. Air enters at the inducer (shaded) and leaves at the exducer, the outer tip. Trim is (inducer ÷ exducer)² × 100.

Spool
The turbo accelerating to the speed where it makes boost.
Boost threshold
The lowest engine speed at which the turbo makes useful boost at full throttle.
Lag
The delay between opening the throttle and boost arriving, once above the threshold.
Pressure ratio
Absolute outlet pressure divided by inlet pressure. 14.5 psi of boost at sea level is about 2.0.
Surge
Too little flow for the pressure ratio. Air stalls and reverses through the wheel, which loads the thrust bearing.
Choke
The compressor's flow limit. Past it, efficiency falls and intake temperature rises quickly.
Frame size
The family a turbo belongs to, such as T25, T3, GT28 or TD04. Parts usually interchange only within a family.
Blow-off valve
Vents boost from the intake when the throttle closes. It does not limit boost pressure.

Sizing

Your engine’s airflow plotted on a compressor map. Left of the surge line, the compressor is too big for that boost; past the choke side, it is too small.

On the map from 4000 rpm, using 52% of its flow at redline.

24.0 lb/min at redline (about 240 hp), pressure ratio 1.82.

01020304050601.01.52.02.53.03.5Airflow, lb/minPRsurge linechoke2k3k4k5k6k7k

The maps here are approximate, so check the manufacturer’s map before buying. This checks the compressor only; how soon the turbo spools depends on the turbine.

Names

Garrett and Mitsubishi names encode the frame, wheel size and bearing type.

GT
Garrett GT family.
28
Turbine frame size (GT28).
71
Compressor exducer, about 71 mm.
R
Ball bearing.

T3/T4 hybrids

  • A T04 compressor housing and wheel on a T3 centre section and T3 turbine.
  • It flows more air than a T3, spools sooner than a full T4, and bolts to a T3 manifold.
  • The name tells you what fits, not how big it is. Check the trim and A/R.
  • T04B and T04E are compressor housing types; the T04E takes larger wheels.
T3T3 compressor, T3 turbine
T3/T4 hybridT04 compressor, T3 turbine
T4T04 compressor, T4 turbine

Bearings and cooling

Journal bearingThe shaft runs on an oil film inside bronze bushings. Cheap, durable and easy to rebuild.
Ball bearing (Garrett "R")Ceramic ball bearings. Less friction, so boost arrives sooner. Needs a restricted oil feed.
Oil feed and drain
Every turbo needs both. The drain works by gravity, so keep it large, short and running downhill to the sump.
Water cooling
Coolant through the centre section stops oil coking in the bearings after a hot shutdown. Connect the ports if the core has them.
Oil restrictor
Ball bearing cores usually need one in the feed. Too much oil pressure pushes oil past the seals and causes smoke.

Wastegates

A wastegate lets exhaust bypass the turbine, which caps boost at the actuator’s spring pressure.

Boost 7.0 psiGate 83% open

The gate is open, holding 7 psi.

Internal
A flapper valve built into the turbine housing. Simple to fit, but boost can creep up at high exhaust flow.
External
A separate valve on the manifold. Holds boost more steadily, and needs a gate port on the manifold and a housing without a flapper.
Spring pressure
The lowest boost the system will run. A boost controller holds the gate shut for more.
Electronic actuator
A motor in place of the spring, so the ECU sets the gate position directly.

Setting up closed-loop boost is covered in the boost control guide.

Flanges

The inlet bolts to the manifold and the outlet to the downpipe. Inlets are drawn to the same scale; overlay two to check whether the bolt holes line up.

1084.25″863.39″44.51.75″66.42.61″57.22.25″44.71.76″1 in (25.4 mm)

T3

The most common inlet: T3, T3/T4 hybrids, GT30 and many GTX.

Plate
108 × 66.4 mm
4.25 × 2.61 in
Bolt spacing
86 × 44.5 mm
3.39 × 1.75 in
Port
57.2 × 44.7 mm
2.25 × 1.76 in
Thickness
11 mm (0.43 in)
5-bolt outlet
Used on T25, GT28 and T3 housings.
V-band outlet
Used on GT30, GTX, G series and most current housings.
Divided inlet
Twin-scroll. Spools sooner when paired with a divided manifold.
Car-specific
Factory turbos such as the TD04 and IHI units. They only fit the car they came on.

Build a turbo

Pick a core, then the parts around it. Options that fit come first in each list.

Bolts together

T3/T4 hybrid, T04E 57 trim

Bearing
Journal
Cooling
Oil
Compressor
T04E 57 trim, about 46 lb/min (~460 hp)
Turbine
T3, 0.63 A/R
Inlet flange
T3
Outlet flange
5-bolt
Wastegate
Internal
  • Compressor to coreFits with a T04 backplate, which makes this a T3/T4 hybrid.
  • Turbine housing to coreT3 housing on a T3 turbine wheel.
  • Inlet flange to manifoldT3 to T3.
  • Outlet flange to downpipe5-bolt to 5-bolt.
  • WastegateInternal gate in the housing.

This covers the common families only. Specific models are in the turbo listing.